Jim's Supply's Home Page  
Vineyard Division Home Page
Accessories for Stakes & Crossarms
Accessories for Wire
Anchors
Crossarms
End Post
Fasteners
Fencing & Netting
Grapestakes & Posts
Miscellaneous Products
Planting & Wire Guide
Quote Request
T-Post & Fencing Posts
Tension Clips & Ties
Tie Tape & Tying Tools
Tools & Scales
Trellis Systems
Tube & Vine Protection
Wire
Wood Stakes & Posts
Installation
Catalog Request
  EARTH ANCHORS | DUCKBILL ANCHORS | DRIVER RODS

ANCHORS   

Tie back wire from end post to anchor

End post with anchor

 

Click on picture to see enlarged photo.

Anchor with tie back wire

Anchor with wire holding tension on end post

 

 

 

 

End Post wires attached to metal anchors hold the tension in the rows.  Wire guards, available in many colors, are useful when applied to the anchor wires for visibility when running mechanical equipment in the rows. For wire tightening and repair devices go to Accessories for Wire.  In some applications, driver rods rather than wire may be used with the anchors.

EARTH ANCHORS
DESCRIPTION SIZE
1  636 EARTH ANCHOR 36" X 6"
2  648 EARTH ANCHOR 48" X 6"
3  848 EARTH ANCHOR 48" X 8"
4  860 EARTH ANCHOR 60" X 8"
5  866 EARTH ANCHOR 66" X 8"


Full range of sizes
 for every job

Various anchor sizes

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

images/anchor_npost.jpg

 

 

 

 

A.B. CHANCE ANCHOR - SPECIFICATIONS
CATALOG
NUMBER
OVERALL
LENGTH
ROD
DIAMETER
EYE-INSIDE
DIAMETER
HELIX
DIAMETER
HOLDING POWER IN NORMAL SOIL PACKED SHIPPING
WEIGHT
315SA 15" 7/16 1" 3" 200 lbs 12/carton 12lbs / carton
330SA 30" 7/16 1" 3" 1,400 lbs 12/carton 22 lbs / carton
430SA 30" 1/2" 1" 4" 2,500 lbs 12 each 30 lbs / pack
430TS 30" 11/16" 1 1/2" 4" 2,500 lbs 6 each 24 lbs / pack

EARTH ANCHORS | DUCKBILL ANCHORS | DRIVER RODS

DUCKBILL Anchors & Drive Rods

 

DUCKBILL'S patented "Star Drive Point" drives straight into the ground at an angle and will not wander from its drive path.

Duckbill insertion
   Duckbill Anchor end view

Duckbill anchors are drive into the ground vertically with a minimum of penetration resistance which compacts and does not disturb the soil it pulls against once driven to the required depth, an upward pull on the cable planes (rotates) the Duckbill into a load lock position at approximately 15 degrees from horizontal. Further upward tension causes the anchor to plane sideways through the earth, against undisturbed soil, resisting pullout and increasing holding of power.

Upward tension on Duckbill Anchors

 

    

 

 

 

 

 

Duckbill anchors are especially useful when staking trees.

SPECIFICATIONS    
Model Number Holding Power in Normal Soil SAFETY FACTOR Min. Cable Breaking Strength Galvanized Steel Cable Cable Length Anchor Weight Standard Pak And Weight
40-DB1 300 lbs 480 lbs 1/16", 7 x 7 20" 1 oz. 50/box
3.7 lbs.
68-DB1 1,100 lbs 1,700 lbs 1/8", 7 x 7 2 1/2 ft. 4.5 oz. 24/box
7 lbs.
¹88-DB1 3,000 lbs 7,000 lbs 1/4", 7 x 19 3 1/2 ft. 14 oz. 12/box
11 lbs.
¹138-DB1 5,000 lbs 9,800 lbs 5/16", 7x19 5 ft. 2.5 lbs. 12/box
32 lbs.

   138 has a wear resistant thimble eye in top of loop.

Duckbill Anchor Sizes

 

 

 

 

 

 

 

                                                                                                            

EARTH ANCHORS | DUCKBILL ANCHORS | DRIVER RODS

 

DRIVER RODS

 

 

ANCHOR APPLICATIONS
SOIL CLASSIFICATION DATA
Class Common Soil-type Description Geological Soil Classification Probe
Values in lbs.
(Nm.)
Typical
Blow Count ASTM-D1586
0 Sound hard rock, unweathered Granite, Basalt, Massive Limestone N.A. N.A. ROD - 50%
1 Very dense and/or cemented sands coarse gravel and cobbles Caliche, (nitrate-bearing gravel/rock, weathered sandstone) 750-1600
(90-208)
60-100+
2 Dense fine sand, very hard silts and clays (may be preloaded) Basal till; boulder clay; caliche; weathered laminated rock 600-750
(65-78)
35-50
3 Dense clays, sands and gravel; hard silts and clays Glacial till; weathered shales, schist, gneiss and silstone 500-600
(65-78)
35-50
4 Medium dense sandy gravel; very stiff to hard silts and clays Glalacial till; hardpan; marls 400-500
(52-65)
24-40
5 Medium dense coarse sand and sandy gravels; stiff to very stiff silts and clays Saprolites, residual soils 300-400
(39-52)
14-25
6 Loose to medium dense fine to coarse sand; firm to stiff clays and silts Dense hydraulic fill; compacted fill; residual soils 200-300
(26-39)
7-14
**7 Loose fine sand; Alluvium; loess; soft-firm clays; varied clays; fill Flood plain soils; lake clays; adobe; gumbo,fill 100-200
(12-26)
4-8
**8 Peat, organic, silts; inundated silts, fly ash Miscellaneous fill, swamp marsh less than 100
(0-13)
0-5
 Class 1 soils are difficult to probe consistently and the ASTM blow count may be of questionable value.
** It is advisable to install anchors deep enough, by the use of extensions, to penetrate a Class 5 or 6 underlying the Class 7 or 8 Soils.


EARTH ANCHORS | DUCKBILL ANCHORS | DRIVER RODS

APPLICATION GUIDE
POWER-INSTALLED SCREW ANCHORS
HELIX
DIAMETER
(INCHES)
SOIL-ANCHOR HOLDING CAPACITY
POUNDS
CLASS 7 CLASS 6 CLASS 5 CLASS 4 CLASS 3 CLASS 2 CLASS 1**
Single 6 * * * * 12,000 24,000 36,000
Single 8 7,000 8,000 10,000 14,000 29,000 24,000 36,000
Single 10 9,000 12,000 16,000 20,000 24,000 28,000 36,000***
Single 12 13,000 19,500 23,000 26,000 30,000 34,500 *
Twin 4 * * * * 12,000 24,000 *
Twin 8 10,000 12,000 19,000 25,000 30,000 36,000 *
Twin 10 10,000 19,000 25,000 30,000 36,000 * *
Holding capacities are based on the average of tests and offered as an application guide only. More specific data on the soils in any area can be obtained by contacting your Chance representative.
   *NOT PRACTICAL TO INSTALL IN THIS SOIL CLASS
     **LIMITED TO USE OF SQUARE ONE ANCHORS

       *** HOLDING CAPACITY LIMITED BY STRENGTH OF 1" ROD

 

ANCHOR ROD STRENGTH
NORMAL ROD DIAMETER ULTIMATE STRENGTH
5/8" 16,000 lbs.
3/4" 23,000 lbs.
1" 36,000 lbs.

NOTE: The anchor rod is a basic part of the PSI system
and holding strength is limited by the strength of the rod
in many cases. Limitations imposed by rod strength are
shown in the table.

Copyright © 2003 Jim's Supply Co, Inc., 800-423-8016, 661-324-6514, jimssci@jimssupply.com . All rights reserved.
Revised: January 10, 2008